The black mark minimum width horizontal should be 14mm on the left edge of media. Select Install printer drivers and Click “Next” 6. When it does, the printer will automatically resume operation. All specifications and signs are subject to change without notice. This build-up can accumulate dust and debris. Parallel Interface Requirements The required cable IEEE compliant is recommended must have a standard pin parallel connector on one end, which is plugged into the parallel port located on the back of the printer. Follow Steps 1 to 8 listed in Standard Mode above.

Uploader: Taushura
Date Added: 27 March 2005
File Size: 50.11 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 27325
Price: Free* [*Free Regsitration Required]

There are two parts to this manual, an operation guide and related information. Surface of heaters should NOT be hit or scratched by sharp or hard things to prevent any damage by scratch. Comments to argox os-2140 ppla Manuals Your Name.

Please pplz to Appendix I. Got it, continue argox os-2140 ppla print. Unwrap the ribbon roll pack and separate the ribbon roll and the bare core. Cutting occurs only when the software is properly set. Thread the media over the platen roller, then route the media through the slot of the cutter module.

Argox OS-214 plus User Manual

Make sure the power switch is in the “O” position. Plug the cutter’s connector into the PCB’s header connector J9. Ground Shorted to Argox os-2140 ppla 1 Note: Driver Windows 7 Label Printer Bixolon. Important notice during TPH To minimize electrical noise pickup in the cable: Lift the top cover to expose the media compartment. Remove the two screws under the base housing. The “FEED” button argox os-2140 ppla not ps-2140 the printer cut.

Driver Argox OS-214 Plus

Page 30 FEED button. Failure to clean the print head, media path, and media sensor could result in inadvertent loss off labels, label argox os-2140 ppla and possible damage pplz the printer.

Serial rs Interface Requirements Serial RS Interface Requirements The required argox os-2140 ppla must have a nine-pin “D” type male connector on one end, which is plugged into the mating serial port located on the back of the pppa. Select Install printer drivers and Click “Next” 6.

Try This:  ADAPTEC AIC-7870 PCI SCSI CONTROLLER EMULATED DRIVER FOR WINDOWS

ARGOX OS PLUS USER MANUAL Pdf Download.

Load the media roll onto the argox os-2140 ppla from left to right. Secure the two screws for the base housing. Driver Windows 7 Label Printer Beiyang. By pressing ‘print’ button you will print only current arggox. This manual also for: Table Of Contents Recovery Lead the media over argox os-2140 ppla platen roller. Select the port of the printer and click “Next”. Don’t show me this message again.

This build-up can accumulate dust and debris. Driver Windows label Printer Ring.

Page 55 Special Caution: Standard mode allows you to collect each label freely. Driver Windows 7 label Printer Citizen. Connecting the Power Supply Connect argox os-2140 ppla power supply as below.

Driver Argox OS Plus | Bz Tech

The other end of the argox os-2140 ppla interface cable connects to the printer connector at the host computer. Push the print head firmly into the casing and shift it to the left. Argox os-2140 ppla example, RTC card and Add-on card. Check if the communication cable parallel or serial is connected securely to your parallel or serial port on the PC and to the connector on the printer at the other end.

This section does not apply to direct thermal printing.

Print Head Assembly 5. Argox OSplus User Manual 44 pages. Insert the ribbon roll into the supply holder. Fonts, Bar Codes argox os-2140 ppla Graphics Specification The specifications of fonts, bar codes and graphics depends on the printer emulation.